This consolidation is unofficial and is for reference only. For the official version of the regulations, consult the original documents on file with the Registry of Regulations, or refer to the Royal Gazette Part II. Regulations are amended frequently. Please check the list of Regulations by Act to see if there are any recent amendments to these regulations filed with our office that are not yet included in this consolidation. Although every effort has been made to ensure the accuracy of this electronic version, the Registry of Regulations assumes no responsibility for any discrepancies that may have resulted from reformatting. This electronic version is copyright © 2017, Province of Nova Scotia, all rights reserved. It is for your personal use and may not be copied for the purposes of resale in this or any other form.
Instrumentation and Control Technician Trade Regulations
made under Section 17A of the
Apprenticeship and Trades Qualifications Act
S.N.S. 2003, c. 1
N.S. Reg. 214/2016 (October 5, 2016, effective April 1, 2017)
1 These regulations may be cited as the Instrumentation and Control Technician Trade Regulations.
2 (1) In these regulations,
“Act” means the Apprenticeship and Trades Qualifications Act;
“General Regulations” means the Apprenticeship and Trades Qualifications Act General Regulations made under the Act;
“instrumentation and control technician trade” means the occupation of an instrumentation and control technician, consisting of installing, adding, altering, calibrating, repairing, maintaining, conducting trials on, testing and commissioning measuring and control devices associated with process industries, including digital, analog, mechanical, electrical, electronic, pneumatic, hydraulic and test instruments.
(2) A term defined in the General Regulations has the same meaning when used in these regulations.
Term of apprenticeship for instrumentation control technician trade
3 (1) The term of apprenticeship for the instrumentation and control technician trade consists of all of the following:
(a) 7200 documented hours of the combination of practical experience and the portion of technical training spent learning the skills of the designated trade as described in clause 26(1A)(a) of the General Regulations and as approved by the Director;
(b) related technical training as described in clause 26(1A)(b) of the General Regulations and as approved by the Director;
(c) a certification examination.
(2) Any probationary period included in a term of apprenticeship for the instrumentation and control technician trade as permitted by subsection 12(2) of the General Regulations must be no longer than 3 months.
Ratio of journeypersons to apprentices for instrumentation and control technician trade
4 The minimum ratio of journeypersons to apprentices required by clause 27(2)(a) of the General Regulations to be maintained by an employer in the instrumentation and control technician trade, unless varied in accordance with Section 24 of the General Regulations, is 1 journeyperson to each apprentice.
Wage schedule for apprentices in instrumentation and control technician trade
5 (1) Subject to subsection (2) and to subsection 25(3) of the General Regulations, the minimum wage for each hour worked by an instrumentation and control technician apprentice in each portion of a level in their term of apprenticeship is a percentage of the wage for an instrumentation and control technician journeyperson in the same place of employment, as set out in the following table:
Wages for Instrumentation and Control Technician Apprentice
Level of Apprenticeship
Hours in Portion of
Level of Apprenticeship
(% of journeyperson’s wage)
(2) An employer must not employ an instrumentation and control technician apprentice at a wage for actual hours worked that is lower than the wage that would be paid at the minimum wage rate prescribed in the Minimum Wage Order (General) made under the Labour Standards Code.
Certificate in instrumentation and control technician trade through trade qualification
6 The period of employment in the designated trade that is required by paragraph 30(1)(a)(ii)(B) of the General Regulations for a person who does not hold a certificate of apprenticeship and is applying for a certificate of qualification in the instrumentation and control technician trade is 10 800 hours.
Compliance with identity card requirements of General Regulations
7 For the purposes of Section 34 of the General Regulations, which requires an apprentice or journeyperson to keep their identity card in their possession when practising the designated trade and produce it on request, a person is practising the instrumentation and control technician trade while the person is doing any of the following:
(a) for an apprentice,
(i) acquiring practical experience in the trade, or
(ii) learning the skills of the trade during the technical training portion of apprenticeship training;
(b) for a journeyperson, performing the duties of the trade as defined in these regulations or their duties as set out in the General Regulations.
8 A person who, immediately before the coming into force of these regulations, was an apprentice in an apprenticeship program under the Instrumentation and Control Technician Trade Regulations, N.S. Reg. 293/2009, continues as an apprentice in that apprenticeship program under these regulations.